CITROEN Saxo International Multipoint CDS roll cage kit. FIA Certificated

Cage Information

Multipoint (weld-in) roll cage:

These have a minimum of 8 point attachments.

Please note, HOWEVER – Because our roll cage will fit very closely to the body-shell it would be normal practice to weld the cage to the shell in at least an additional 8 or 10 places, (and sometimes many more) making a minimum of 16 points.

Weld-in roll cage kit:

Our weld-in kits are supplied with all the parts you need to fit a roll cage.

All the tubes are pre-cut and profiled to fit.

They come complete with the footplates that get welded to the car, as well as all relevant gussets.

FIA Certificated Cages:

Fully certificated roll-cage designs give a distinct advantage over roll-cages constructed to minimum compliance as they are constructed using a small diameter / thinner gauge tube, thus giving a considerable weight saving.

Depending on the make & model, a fully certificated roll cage gives you the ability to compete in FIA International events and feature the following:

A certificated design is manufactured to meet the FIA / MSUK Roll Cage Homologation Regulations.
Usually, a ‘Multi-point’ design which adds stiffness and strength to the bodyshell.
These are almost always a ‘weld-in’ cage which is lighter and stiffer than a ‘bolt-in’ cage.
The designs are stress tested to prove their integrity and geometry, and tube sizes are optimised to give the best strength-to-weight ratio.
We always use high-tensile tube for these designs (normally T45, which has a tensile strength of min. 700 Mpa) to further enhance their advantages.
An FIA / MSUK certificated roll cage is accepted worldwide and enables competitors to run in any FIA-sanctioned event.
Can be as much as 20 kg lighter than an MSUK compliant design.
When correctly installed, they add value and saleability to a vehicle.
They are authorised in the UK by MSUK (the MSA as was), but the certificates are still referred to as FIA papers.
These regulations are constantly evolving, so new designs have to reflect these changes.

Please contact sales@customcages.co.uk for more details.

MSUK Compliant – See our ‘National’ range:

The roll cage will be made using the minimum MSUK prescribed tube sizes – thicker gauge than we would use in a certificated design, and, so (unfortunately) heavier.

Usually, these are manufactured from CDS (Cold Drawn Seamless) tube – ours is a high tensile material with a minimum tensile strength of 510 Mpa – although T45 can be specified at extra cost.

These cages are eligible for all MSUK events.

Find Out More >

Additional Information

Brand:

Citroen

Car Model(s):

Saxo

Cage Options:

CDS, Weld-in kit

Fitting Type:

Multipoint

Cage Type:

FIA Certified, MS UK Compliant, Multipoint

Suitable for:

Hillclimb, Sprints, Time attack, Track days

Weight:

42.0

Download Pdf >

Roll Cage Kit Contents

Your roll cage arrives shrink-wrapped in durable black plastic. And by the way, it is very heavy!

Inside you will find:

CNC formed tubes for the main hoop, A pillar hoops etc with square and profiled ends are necessary.
Straight tubes with profiled ends ready for welding into place.
Set of footplates.
Check list (every tube has an identifying sticker) so you can be sure you have a complete kit (we will have already have checked that you have the right tubes twice before the kit is packed).
Instructions sheet.
CD showing the fully fitted roll cage.

Roll Cage Certification

A roll cage design must comply with the MSA/FIA technical regulations published in the MS UK Blue book. It is the competitor’s responsibility to ensure his/her roll cage complies with the technical regulations appropriate to the event they are competing in.

To compete in any race or rally your roll cage will need to comply with either MSA or FIA regulations. (Effectively, the MSA is governed by the FIA so if a roll cage design complies with FIA regs, then it is also eligible for MSA events). There are some instances where the FIA allows certain design features where the MSA do not (and vice versa).

The certification process generally allows for a lighter roll cage because it is a bespoke design where the diameter and thickness of each tube is optimised to achieve the overall strength required by the FIA/MSA rules.

In order to compete in MSA/FIA events every vehicle, which has a certificated design of roll cage, should have a copy of a valid certificate to present at scrutineering. Custom Cages has certified the majority of popular roll cages. All other roll cages comply with MSA/FIA regulations and receive a Letter of Conformity for competitors to present to scrutineers.

To obtain a certificate for a self-fit roll cage, the installer must complete a Custom Cages weld test.

Custom Cages’ roll cage kits include a weld test sample. Once completed these are returned to the company for load testing. They are subjected to a physical test to assess the actual yield strength of the weld. This ensures that the self-fit roll cages achieve the highest standards of integrity.

Additional samples may be requested.

Certificates will only be issued on completion of a successful test.

Please be aware that there is a charge of £60.00 + VAT for all MS UK / FIA Certificates

Categories

Products

BMW E46 2dr 6 point National Spec CDS roll cage kit. MS UK Compliant

BMW E46 2dr International Multipoint T45 roll cage kit. FIA Certificated

BMW E46 2dr Step 2 International Multipoint T45 roll cage kit. FIA Certificated

BMW E46 4dr 6 point National Spec CDS roll cage kit. MS UK Compliant

BMW E46 4dr Step 2 International Multipoint T45 roll cage kit. FIA Certificated

BMW E46 Compact 6 point National Spec CDS roll cage kit. MS UK Compliant

BMW E46 Compact Bolt-in CDS roll cage MS UK Compliant

BMW E46 Compact International Multipoint T45 roll cage kit. FIA Certificated

BMW E90 International Multipoint T45 roll cage kit. FIA Certificated

BMW E90 / E92 Optima Multipoint T45 Roll Cage FIA Certificated

BMW E92 International Multipoint T45 roll cage kit. FIA Certificated

BMW E92 Rear Half Bolt-in T45 Roll Cage

BMW M1 Historic T45 roll cage kit. MS UK Compliant to Appendix K

BMW M2 F87 6 point National Spec roll cage kit. MS UK Compliant

BMW M2 F87 Multipoint T45 roll cage kit

BMW M6 E24 Multipoint CDS roll cage kit.

BMW M6 E24 Multipoint T45 roll cage kit

BMW Mini 2nd gen 2007 on R56 6 point National Spec CDS roll cage kit. MS UK Compliant

BMW Mini 2nd gen 2007 on R56 Multipoint T45 roll cage kit.

BMW Mini Clubman F54 Multipoint T45 roll cage kit.

BMW Mini Countryman R60 Multipoint T45 roll cage kit

BMW Mini R50 and R53 6 point National Spec CDS roll cage kit MS UK Compliant

BMW Mini R50 and R53 International Multipoint CDS roll cage kit. FIA Certificated

BMW Mini R50 and R53 International Multipoint T45 roll cage kit. FIA Certificated

Categories

Products

1"1/2 Lap Joint

1"3/4 FIA Lap Joint

1.5m CDS Tube 40 x 2.0mm

1.5m T45 Tube 40 x 2.0mm

35mm FIA Lap Joint

40mm FIA Lap Joint

45mm FIA Lap Joint

AC Cobra Historic T45 roll cage

AC Cobra Daytona Historic T45 roll cage

ALFA ROMEO 105 GTA Historic T45 roll cage kit. FIA Appendix K certificated

ALFA ROMEO 145 Multipoint CDS roll cage kit

ALFA ROMEO 145 Multipoint T45 roll cage kit

ALFA ROMEO 145 National Spec 6 Point CDS roll cage kit. MS UK Compliant

ALFA ROMEO 147 GTA 6 point National Spec CDS roll cage kit. MS UK Compliant

ALFA ROMEO 147 GTA International Multipoint T45 roll cage kit. FIA Certificated

ALFA ROMEO 147 GTA Multipoint CDS roll cage kit

ALFA ROMEO 75 GTV Coupe Multipoint T45 roll cage kit.

ALFA ROMEO Alfasud Multipoint T45 roll cage kit.

ALFA ROMEO Guilia Saloon Historic CDS roll cage kit. MS UK Compliant to Appendix K

ALFA ROMEO Guilia Saloon Historic T45 roll cage kit. MS UK Compliant to Appendix K

ALFA ROMEO Junior Zagato Multipoint T45 roll cage kit. MS UK Compliant

ALFA ROMEO Spyder (`63) Historic CDS roll cage kit. MS UK Compliant to Appendix K

ALFA ROMEO Spyder (`63) Historic T45 roll cage kit. MS UK Compliant to Appendix K

ALFA ROMEO TZ Historic CDS roll cage kit. MS UK Compliant to Appendix K

ALFA ROMEO TZ Historic T45 roll cage kit. MS UK Compliant to Appendix K

ALFA ROMEO TZ Multipoint T45 roll cage kit.

ALLARD J2 Historic CDS roll cage kit. MS UK Compliant to Appendix K

ALLARD J2 Historic T45 roll cage kit. MS UK Compliant to Appendix K

ASTON MARTIN DB3S Bolt-in T45 roll cage

ASTON MARTIN DB4 Bolt-in CDS roll cage MS UK Compliant

ASTON MARTIN DB4 International Historic T45 roll cage kit. FIA Certificated to Appendix K

ASTON MARTIN DB7 6 point Clubman CDS roll cage kit. MS UK Compliant

AUDI 80 6 Point National Spec CDS roll cage kit. MS UK Compliant

AUDI 80 Multipoint CDS roll cage kit.

AUDI 80 Multipoint T45 roll cage kit.

AUDI 80 S2 6 point National Spec CDS roll cage kit. MS UK Compliant

AUDI 80 S2 Multipoint CDS roll cage kit.

AUDI 80 S2 Multipoint T45 roll cage kit.

AUDI A3 MK2 Multipoint T45 roll cage kit.

AUDI A3 MK3 Multipoint T45 roll cage kit

AUDI A4 >00 Multipoint T45 roll cage kit

AUDI A4 >00 6 point National Spec CDS roll cage kit. MS UK Compliant

AUDI Quattro LWB Factory Replica Historic T45 roll cage kit. MS UK Compliant to Appendix K

AUDI Quattro LWB Historic T45 roll cage kit. MS UK Compliant to Appendix K

AUDI Quattro LWB Multipoint International Historic T45 roll cage kit. FIA Certificated to Appendix K

AUDI Quattro SWB Factory Style Historic T45 roll cage kit. MS UK Compliant to Appendix K

AUDI Quattro SWB Historic Historic T45 roll cage kit. MS UK Compliant to Appendix K

AUDI Quattro SWB Multipoint T45 roll cage kit

AUDI R8 Multipoint T45 roll cage kit

AUDI TT MK1 6 point National Spec CDS roll cage kit. MS UK Compliant

AUDI TT MK1 Bolt-in T45 roll cage MS UK Compliant

AUDI TT MK1 Multipoint CDS roll cage kit.